Back to Step by Step Course by Robojax
If you don't like to see ads while video is being played you can purchase YouTube premium Here
Please select other codes for this lecture from the links below.
In this lesson we learn how to use mini stepper motor 28BYJ-48 for our project. I am presenting with 8 projects so you can use it in almost any applicaiton. In the video, I have explained the code, shown full wiring diagram and how connect the wires, push buttons and bread board.
In Project 8 STPB-5 we control speed of stepper motor using potentiometer. We set the longest speed and adjust it using potentiometer. Just push and motor goes to that angel. The angles and seped are set int code . See video for details and demonstration.
/*
* Lesson 107-8: * This is Arduino code to control Speed of 28BYj-48
* Stepper motor with potentiometer.
See video for details and demonstration.
In this lesson we learn how to use mini stepper motor 28BYJ-48 for our project. I am presenting with 8 projects
so you can use it in almost any applicaiton. In the video, I have explained the code, shown full wiring diagram and
how connect the wires, push buttons and bread board.
Project 2: we will push different keys on keyboard and control motor
Project 1: Running motor
Project 2: Controlling stepper motor from Serial Monitor
Project 3: Controlling stepper motor using push button STPB-1
Project 4: Controlling using push button STPB-2 keep pressing
Project 5: One Revolution using push button STPB-3
Project 6: Push button Any Angle and speed STPB-4
Project 7: Using multiple buttons to any angles STPB-5 angle, speed and direction
Project 8: Controlling stepper motor using potentiometer (this code)
* Watch Video instrution for this code:https://youtu.be/TQ7R2bY-MWU
*
* This code is part of Arduino Step by Step Course which starts here: https://youtu.be/-6qSrDUA5a8
*
* for library of this code visit http://robojax.com/
*
If you found this tutorial helpful, please support me so I can continue creating
content like this. Make a donation using PayPal by credit card https://bit.ly/donate-robojax
* Written by Ahmad Shamshiri for Robojax Robojax.com
* on Jun 30, 2019 at 19:04 in Ajax, Ontario, Canada
*
*
* * This code is "AS IS" without warranty or liability. Free to be used as long as you keep this note intact.*
* This code has been download from Robojax.com
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <https://www.gnu.org/licenses/>.
*/
const int desiredValue = 20;//time in sec for a Revolution
const int dir = 2; // 1 for CW and 2 for CCW
int Pin1 = 10;//IN1 is connected to 10
int Pin2 = 11;//IN2 is connected to 11
int Pin3 = 12;//IN3 is connected to 12
int Pin4 = 13;//IN4 is connected to 13
int potPin = A0;// center pin of pot is connected to this pin
int vcc2 = 2;// additional 5V for potentiometer
int pole1[] ={0,0,0,0, 0,1,1,1, 0};//pole1, 8 step values
int pole2[] ={0,0,0,1, 1,1,0,0, 0};//pole2, 8 step values
int pole3[] ={0,1,1,1, 0,0,0,0, 0};//pole3, 8 step values
int pole4[] ={1,1,0,0, 0,0,0,1, 0};//pole4, 8 step values
int poleStep = 0;
int calcDelayfromTime(int t);
void driveStepper(int c);
int N = calcDelayfromTime(desiredValue);
void setup()
{
pinMode(Pin1, OUTPUT);//define pin for ULN2003 in1
pinMode(Pin2, OUTPUT);//define pin for ULN2003 in2
pinMode(Pin3, OUTPUT);//define pin for ULN2003 in3
pinMode(Pin4, OUTPUT);//define pin for ULN2003 in4
pinMode(vcc2, OUTPUT);//define pin as output for 5V for pot
digitalWrite(vcc2, HIGH);//set vcc2 pin HIGH to have 5V for pot
Serial.begin(9600);
Serial.println("Robojax Stepper Control");
Serial.print("Max time per rev set: ");
Serial.print(desiredValue);
Serial.print(" loop delay: ");
Serial.println(N);
delay(4000);//give use time to read
}// setup
void loop()
{
// Robojax Stepper code S8BYJ-48
if(dir ==1){
poleStep++;
driveStepper(poleStep);
}else if(dir ==2){
poleStep--;
driveStepper(poleStep);
}else{
driveStepper(8);
}
if(poleStep>7){
poleStep=0;
}
if(poleStep<0){
poleStep=7;
}
int potValue =analogRead(potPin);// read potentiometer value
int speed = map(potValue,0, 1023, 1,N);
delay(speed);
}// loop
int calcDelayfromTime(int t){
return ((t-5)/4)+1;
}//
/*
* @brief sends signal to the motor
* @param "c" is integer representing the pol of motor
* @return does not return anything
*
* www.Robojax.com code June 2019
*/
void driveStepper(int c)
{
digitalWrite(Pin1, pole1[c]);
digitalWrite(Pin2, pole2[c]);
digitalWrite(Pin3, pole3[c]);
digitalWrite(Pin4, pole4[c]);
}//driveStepper end here
The least I expect from you is to thumb up the video and subscribe to my channel. I appriciate that. .I have spent months making these lectures and writing code. You don't lose anything by subscribging to my channel. Your subscription is stamp of approval to my videos and more people can find them and in it turn it helps me. Thank you
If you found this tutorial helpful, please support me so I can continue creating content like this. support me via PayPal
**** AFFILIATE PROGRAM **** We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.