Back to Arduino Step By Step Course

Lesson 53: Using L298N Motor Driver for DC Motor Control | Arduino Step By Step Course | Arduino Step By Step Course

If you don't like to see ads while video is being played you can purchase this course for $200 from Udemy or purchase YouTube premium Here

Please download required files for this code

Part 5: DC Motors

In this lesson we learn how to contorl a DC motor using L298N Motor driver module and Arduino .
Please watch the video for full details.

AliExpress.com Product - 1pcs L298N MOTOR DRIVER module New Dual H Bridge DC Stepper Motor Drive Controller Board Module

  /*
Lesson 53: Using L298N Motor Driver for DC Motor Control
Watch full detailed Video https://youtu.be/fqBLIrwq2YA

 * Library Example for L298N Module to control DC motors
 * 
 * This code is to control single motor. For two motor control, please open L298N_DC_2_Motors
 P
 * 
 * Written by Ahmad Shamshiri on October 01, 2019 at 21:26 
 * in Ajax, Ontario, Canada. www.robojax.com
 * 
 * 
 * Watch video instruction for this code:
 * 

If you found this tutorial helpful, please support me so I can continue creating 
content like this. You can support me on Patreon http://robojax.com/L/?id=63

or make donation using PayPal http://robojax.com/L/?id=64

 *  * This code is "AS IS" without warranty or liability. Free to be used as long as you keep this note intact.* 
 * This code has been download from Robojax.com
    This program is free software: you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
    the Free Software Foundation, either version 3 of the License, or
    (at your option) any later version.

    This program is distributed in the hope that it will be useful,
    but WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
    GNU General Public License for more details.

    You should have received a copy of the GNU General Public License
    along with this program.  If not, see <https://www.gnu.org/licenses/>.
 */

#include <Robojax_L298N_DC_motor.h>
// motor 1 settings
#define IN1 6
#define IN2 7
#define ENA 8 // this pin must be PWM enabled pin
const int CCW = 2; // do not change
const int CW  = 1; // do not change
#define motor1 1 // do not change
// use the line below for single motor
Robojax_L298N_DC_motor motor(IN1, IN2, ENA, true);


void setup() {
  Serial.begin(115200);
  motor.begin();
  //L298N DC Motor by Robojax.com

}

void loop() {
  
  motor.demo(1);
  motor.rotate(motor1, 60, CW);//run motor1 at 60% speed in CW direction
 
  delay(3000);

  motor.brake(1);
  delay(2000);


  motor.rotate(motor1, 100, CW);//run motor1 at 60% speed in CW direction
  delay(3000);

  motor.brake(1);
  delay(2000);  

  for(int i=0; i<=100; i++)
  {
    motor.rotate(motor1, i, CW);// turn motor1 with i% speed in CW direction (whatever is i) 
    delay(100);
  }
  delay(2000);
  
  motor.brake(1);
  delay(2000);  

  motor.rotate(motor1, 70, CCW);//run motor1 at 70% speed in CCW direction
  delay(4000);

  motor.brake(1);
  delay(2000);    
  
}



   

The least I expect from you is to thumb up the video and subscribe to my channel. I appriciate that. .I have spent months making these lectures and writing code. You don't lose anything by subscribging to my channel. Your subscription is stamp of approval to my videos and more people can find them and in it turn it helps me. Thank you

If you found this tutorial helpful, please support me so I can continue creating content like this. support me via PayPal