กระโดดไปยัง:
Lesson 1/1: What is Arduino? Types of Arduino Boards and SunFounder Kit Lesson 2/31: Getting Arduino Software and using Documentation for SunFounder Arduino Kit Lesson 3/31: Project LED Blink, What is Breadboard, LED and Resistor Using SunFounder Kit Lesson 4/31: What are Binary, Decimal, Hexadecimal and Octal Number, Arduino Serial Monitor Lesson 5/31: Introduction to Arduino Data Types SunFounder Learning Kit Lesson 6/31: Buzzer, Driver Wheel and mini Water Pump using Arduino SunFounder Kit | Robojax Lesson 7/31: Digital Read Push button, detecting magnetic field SunFounder Kit | Robojax Lesson 8/31 : AnalogWrite LED Fade, for loop, while loop and do while loops | SunFounder Robojax Lesson 9/31: Reading Voltage Using Arduino, Potentiometer AnalogRead SunFounder Kit | Robojax Lesson 10/31: Conditional Statement in Arduino and Using Array | SunFounder Robojax Lesson 11/31: What is Arduino library and How to use DHT11 Temperature and Humidity Sensor | SunFounder Lesson 12/31: Using Arduino Programming function and switch | SunFounder Robojax Lesson 13/31: Using XY Joystick with Arduino and turning a buzzer with joystick Motion | Robojax Lesson 14/31: Arduino Millis (no delay) and map functions | SunFounder Robojax Lesson 15/31: Using Soil Moisture Sensor with Arduino SunFounder Kit | Robojax Lesson 16/31: Detecting Obstacle Using Infrared Obstacle Avoidance Sensor using SunFounder Kit Lesson 17/31: How to interrupt a delay in Arduino and Light Dependant Resistor LDR | Robojax Lesson 18/31: Using Servo Motor with Arduino SunFounder's Arduino Kit Lesson 19/31: Measure Distance Using Ultrasonic Sensor with Arduino | SunFounder Robojax Lesson 20/31: Using LCD1602 with Arduino display temperature, voltage and distance | Robojax Lesson 21/31: Using Infrared Remote Control with Arduino | SunFounder Robojax Lesson 22/31: Using Seven Segment Display with Arduino and Electronic Dice | SunFounder Robojax Lesson 23/31: Smart Car Part 1: SunFounder Smart Car Assembly and DC Motor Full Bridge Explained Lesson 24/31: Smart Car Part 2: Moving Forward, Reverse, left and right and Controlling Speed of Car Lesson 25/31: Car-3 Smart Car Avoids Obstacle Using Infrared Sensors | SunFounder Robojax Lesson 26/31: Smart Car Part 4 : Avoiding Obstacle Using Ultrasonic Sensor | SunFounder Robojax Lesson 27/31: Car-5 SunFounder Smart Car Follows Your Hand using Arduino | Robojax Lesson 28/31: Car-6 SunFounder self Driving Arduino car using | Robojax Lesson 29/31: Car-7 Controlling SunFounder Smart Car using Remote Controller | Robojax Lesson 30/31: Car-8 Line Tracking by Smart Car from SunFounder Arduino Kit | Robojax Lesson 31/31: Measure Temperature and Humidity Over Wi-Fi using DHT11 and ESP01 SunFounder Kit
Lesson 22/31: Using Seven Segment Display with Arduino and Electronic Dice | SunFounder Robojax
In this lesson, we learn how to create a digital counter using a seven-segment display. We begin by explaining the basics of the seven-segment display and how it works, followed by a detailed walkthrough of the code. The wiring setup is thoroughly explained and supported with diagrams for clarity. In the second project, we build an electronic dice. When a push button is pressed, the numbers cycle from 0 to 6, and upon release, the display randomly stops at a number. Both projects are fully explained, with complete code and wiring instructions provided.
แหล่งข้อมูลและเอกสารอ้างอิง ยังไม่มีทรัพยากรเลย
