Lesson 98: Arduino 10 LED Push button Projects, Potentiometer LED Voltmeter and Traffic Light

Please select other codes for this lecture from the links below.

Part 1: Introduction

In this lesson we learn how to use LED and Push button in this 10 LED projects. Wiring diagram is shown, code is fully explained and demonstrated with multiple change of settings for each project. We read potentiometer's voltage and display voltage by turning each LED on to represent voltages. A Simple traffic light project.
This code is part of video lecture. This project 7 code. this is an Arduino sktech where 4 LEDS turn ON and OFF in such a way that an LED is walking.

1:16 LED and resistor calculation
05:52 Projec 1 LED ON OFF
12:41 Projec 2 LED ON/OFF with push button
17:12 Projec 3 LED ON/OFF toggle with push button
20:10 Projec 4 Fading light of LED
23:17 Projec 5 Fading light of LED using push button
27:30 Projec 6 See Saw with LED using Arduino
30:44 Projec 7 Walking Light Using Arduino
36:38 Projec 8 Walking light with push button using Arduino
42:21 Projec 9, 5 LED voltage level meter using Arduino
49:21 Projec 10 Arduino Traffic Light


 
/*
 * Arduino Step by Step Course by Robojax
 * Lesson 98  https://robojax.com/course1/?vid=lecture98
 * Project 7 of 10
 * 

 * 4 LEDS walking light Arduio Project
 * this is an Arduino sktech where 4 LEDS turn ON and OFF in such a way
 * that an LED is walking

* Watch full details and demonstraiton: https://youtu.be/OSwleCBlkuI
 * 
 * Start a full Arduino Step By Step course:  https://youtu.be/-6qSrDUA5a8
 * 
 *  * LED = Light Emitting Diode
 * LED is pronouced (El EE Dee)
 ****** 10 Projects explained in this video
 * 1-LED ON OFF 
 * 2-LED ON/OFF with push button
 * 3-LED ON/OFF toggle with push button
 * 4-Fading light of LED
 * 5-Fading light of LED using push button
 * 6-See Saw with LED
 * 7-Walking Light
 * 8-Walking light with push button
 * 9-LED voltage level meter
 * 10- Arduino Traffic Light
 * 
 * written by Ahmad Shamshiri on Feb 01, 2022 
 * this code can be obtained from Robojax.com
 * Code ID: WalkingLED
 This video is part of Arduino Step by Step Course which starts here: https://youtu.be/-6qSrDUA5a8

 * www.Robojax.com

If you found this tutorial helpful, please support me so I can continue creating 
content like this. Make a donation using PayPal by credit card https://bit.ly/donate-robojax
  
 * This code is "AS IS" without warranty or liability. Free to be used as long as you keep this note intact.* 
 * This code has been download from Robojax.com
    This program is free software: you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
    the Free Software Foundation, either version 3 of the License, or
    (at your option) any later version.

    This program is distributed in the hope that it will be useful,
    but WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
    GNU General Public License for more details.

    You should have received a copy of the GNU General Public License
    along with this program.  If not, see <https://www.gnu.org/licenses/>.* 
 */
const int LED1 = 3;
const int LED2 = 4;
const int LED3 = 5;
const int LED4 = 6; 
const int LED5 = 7; 
int offTime = 30;//the time LED waits in OFF state
int onTime = 100;//the time LED is ON 

//the code inside setup() runs once.

void setup() {
  pinMode(LED1, OUTPUT);//set pin of Arduino as output
  pinMode(LED2, OUTPUT);//set pin of Arduino as output
  pinMode(LED3, OUTPUT);//set pin of Arduino as output
  pinMode(LED4, OUTPUT);//set pin of Arduino as output
  pinMode(LED5, OUTPUT);//set pin of Arduino as output  
}//setup end

void loop() {
  
  digitalWrite(LED1, HIGH);//set pin 2 to HIGH 
  delay(onTime);    //wait for the onTime seconds (see top of this code)                   
  digitalWrite(LED1, LOW); // Set pin 2 to LOW
  delay(offTime);  //wait for the offTime seconds (see top of this code) 

  digitalWrite(LED2, HIGH);  //set pin 3 to HIGH 
  delay(onTime);      //wait for the onTime seconds (see top of this code)                    
  digitalWrite(LED2, LOW); // Set pin 3 to LOW  
  delay(offTime);  //wait for the offTime seconds (see top of this code)    

  digitalWrite(LED3, HIGH); //set pin 4 to HIGH  
  delay(onTime);     //wait for the onTime seconds (see top of this code)                     
  digitalWrite(LED3, LOW); // Set pin 4 to LOW  
  delay(offTime);   //wait for the offTime seconds (see top of this code)   

  digitalWrite(LED4, HIGH);  //set pin 5 to HIGH 
  delay(onTime);    //wait for the onTime seconds (see top of this code)                      
  digitalWrite(LED4, LOW);  // Set pin 5 to LOW 
  delay(offTime);    //wait for the offTime seconds (see top of this code)                               

  digitalWrite(LED5, HIGH);  //set pin 6 to HIGH 
  delay(onTime);    //wait for the onTime seconds (see top of this code)                      
  digitalWrite(LED5, LOW);  // Set pin 6 to LOW 
  delay(offTime);    //wait for the offTime seconds (see top of this code)                               
// Watch full details and demonstraiton: https://youtu.be/7xTHaFdCyaI
}