Robojax

Lesson 109: Generate DC Voltage using MCP4725 DAC with LCD and PWM to Voltage Converter with Arduino (5 projects)

Lesson 109: Generate DC Voltage using MCP4725 DAC with LCD and PWM to Voltage Converter with Arduino (5 projects)

Please select other codes for this lecture from the links below.

Related or required files and link to this lesson

Part 14: Voltage and Current

In this lesson we learn how to use MCP4725 12 bits Digital To Analog Converter (DAC). The chip and module is explained, datasheet viewed and then using 5 Projects this MCP4725 practically shown. Full wiring diagram and wring shown and how to use the code and library explained.

In Project 1 in lesson 109 Using MCP4725 12bits DAC with Ardunino

Projects

Timing of chapters in the video

00:00 Introduction
1:19 MCP4725 Explained
4:46 Datasheet viewed
7:07 Project 1: Outputting DC Voltage
09:55 Code and library
13:00 Project 1: demonstration
17:34 Triangular wave
18:54 Sine wave
20:18 Project 2: Control voltage from Serial Monitor
22:21 Project 2: Demonstration
24:53 Project 3: Converting PWM to Voltage
27:33 Code Explained
29:25 Wiring explained
30:29 Project 3: Demonstration
33:25 Project 4: Using two MCP4725 modules
36:27 Project 4: Demonstration
37:30 Project 5: Setting output with push buttons on LCD
39:57 Code explained
45:53 Project 5: Demonstration

  /* 
 * Lesson 109-1: Generates output DC Voltage from 0 to 5.5V or lower. if power supply
 *  is 3.3V, then max voltage is 3.3V.
 * you can use it simply to enter your request as millivolt like 365mV
 * or 2.872V
 * 
 * * Watch Video instrution for this code:https://youtu.be/j_BwZT9z-0g
  
Projects in this video: https://youtu.be/j_BwZT9z-0g
Project 1 (this project):Output 0 to 5V or 0 to 3V depending on which kind of power sources you use for the module. The output shown on digital multimeter. 
Project 2: Serial command to set voltage
Project 3: PWM duty cycle to Voltage converter
Project 4: Using two MCP4725 DAC modules
Project 5: Using Push button to set voltage on LCD

 * Written by Ahmad Shamshiri using Adafruit library for MCP4725
 Sep 26, 2022
 www.Robojax.com
 
  
   * 
   * This code is part of Arduino Step by Step Course which starts here:  https://youtu.be/-6qSrDUA5a8
   * 
   * for library of this code visit http://robojax.com/
   * 
  If you found this tutorial helpful, please support me so I can continue creating 
  content like this. Make a donation using PayPal by credit card https://bit.ly/donate-robojax 
  
 
  
   *  * This code is "AS IS" without warranty or liability. Free to be used as long as you keep this note intact.* 
   * This code has been download from Robojax.com
      This program is free software: you can redistribute it and/or modify
      it under the terms of the GNU General Public License as published by
      the Free Software Foundation, either version 3 of the License, or
      (at your option) any later version.
  
      This program is distributed in the hope that it will be useful,
      but WITHOUT ANY WARRANTY; without even the implied warranty of
      MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
      GNU General Public License for more details.
  
      You should have received a copy of the GNU General Public License
      along with this program.  If not, see <https://www.gnu.org/licenses/>.
 

    Based on  the Adafruit MCP4725 Library
    ----> http://www.adafruit.com/products/935

    Adafruit invests time and resources providing this open source code,
    please support Adafruit and open-source hardware by purchasing
    products from Adafruit!
*/

#include <Wire.h>
#include <Adafruit_MCP4725.h>
int refV = 4530;//reference voltage. see video for details

Adafruit_MCP4725 dac;
int mV;
float V;

void setup(void) {
  Serial.begin(9600);
  Serial.println("MCP4725 by Robojax");
  
  //run i2C scanner to find out the I2C address and enter it below
  //see video for details https://youtu.be/j_BwZT9z-0g
  //get more code from www.Robojax.com   
  dac.begin(0x60);

  Serial.println("Output Voltage");
}

void loop(void) {

//    setmV(465);//set output to 465mV
//    Serial.print(mV);
//    Serial.println("mV");
//    delay(5000);
//    
//    setV(2.635);//set output to 2.6V
//    Serial.print(V, 3);
//    Serial.println("V");
//    delay(5000);
//    Serial.println();

    for(int i=0; i<refV; i +=100)
    {
      setmV(i);
      Serial.println(i);
      
    }
  //see video for details https://youtu.be/j_BwZT9z-0g
  //get more code from www.Robojax.com 
}

/*
 * setmV()
 * sets mV value such as 35mV or 2654mV (2.654V)
 * Written Sep 25, 2022
 * by Ahmad Shamshiri www.Robojax.com
 */
void setmV(int d)
{
  
    mV =d;
    dac.setVoltage(map(d, 0, refV, 0, 4095), false);

}


/*
 * setV()
 * sets Voltage value value in volts such as 3.764
 * Written Sep 25, 2022
 * by Ahmad Shamshiri www.Robojax.com
 */
void setV(float d)
{
    V = d;
    dac.setVoltage( map((d *1000), 0, refV, 0, 4095), false);

}